收藏本站
BU9883FV-W
Datasheet
3. Set SDA0 to 3 and SCL0 to 3 so as not to become 'Hi-Z'.
When the above conditions 1 and 2 cannot be observed, take the following countermeasures.
a) In the case when the above condition 1 cannot be observed. When SDA0 to 3 becomes 'L' at power on.
→ Control SCL0 to 3 and SDA0 to 3 as shown below, to make SCL0 to 3 and SDA0 to 3, 'H' and 'H'.
V CC
SCL
SDA
After Vcc becomes stable
t LOW
After Vcc becomes stable
t DH
t SU:DAT
t SU:DAT
Figure 59. When SCL0 to 3= 'H' and SDA0 to 3= 'L'
Figure 60. When SCL0 to 3='L' and SDA0 to 3='L'
b) In the case when the above condition 2 cannot be observed.
→ After power source becomes stable, execute software reset(Page 19).
c) In the case when the above conditions 1 and 2 cannot be observed.
→ Carry out a), and then carry out b).
● Low voltage malfunction prevention function
LVCC circuit prevents data rewrite action at low power, and prevents wrong write. At LVCC voltage (Typ. =1.2V) or below, it
prevent data rewrite.
● V CC noise countermeasures
○ Bypass capacitor
When noise or surge gets in the power source line, malfunction may occur, therefore, for removing these, it is
recommended to attach a by pass capacitor (0.1 μ F) between IC V CC OUT and GND. At that moment, attach it as close to
IC as possible. And, it is also recommended to attach a bypass capacitor between board V CC OUT and GND.
● Cautions on use
(1) Described numeric values and data are design representative values, and the values are not guaranteed.
(2) We believe that application circuit examples are recommendable, however, in actual use, confirm characteristics further
sufficiently. In the case of use by changing the fixed number of external parts, make your decision with sufficient margin
in consideration of static characteristics and transition characteristics and fluctuations of external parts and our LSI.
(3) Absolute maximum ratings
If the absolute maximum ratings such as impressed voltage and action temperature range and so forth are exceeded,
LSI may be destructed. Do not impress voltage and temperature exceeding the absolute maximum ratings. In the case
of fear exceeding the absolute maximum ratings, take physical safety countermeasures such as fuses, and see to it
that conditions exceeding the absolute maximum ratings should not be impressed to LSI.
(4) GND electric potential
Set the voltage of GND terminal lowest at any action condition. Make sure that each terminal voltage is lower than that
of GND terminal.
(5) Terminal design
In consideration of permissible loss in actual use condition, carry out heat design with sufficient margin.
(6) Terminal to terminal shortcircuit and wrong packaging
When to package LSI onto a board, pay sufficient attention to LSI direction and displacement. Wrong packaging may
destruct LSI. And in the case of shortcircuit between LSI terminals and terminals and power source, terminal and GND
owing to foreign matter, LSI may be destructed.
(7) Use in a strong electromagnetic field may cause malfunction, therefore, evaluate design sufficiently.
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a reference
to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority.
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
23/25
TSZ02201-0R2R0G100420-1-2
31.AUG.2012 Rev.001
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
BU9889GUL-WE2 IC EEPROM 8KBIT 2WIRE VCSP50L1
BU9891GUL-WE2 IC EEPROM 4KBIT VCSP T/R
BU9897GUL-WE2 IC EEPROM SERIAL VCSP50L2
BU99901GUZ-WE2 IC EEPROM 32KBIT 2WIRE VCSP
BUK218-50DY,118 TOPFET DUAL SWITCH D2PAK
BVL121200003N BATTERY CHG UNIV 12VDC @ 1.2A
BVW241250003A BATTERY CHG UNIV 24VDC @ 1.25A
C-14245 RACKMOUNT INTERNAL CHASSIS
相关代理商/技术参数
BU9888FV-W 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs
BU9888FV-WE2 制造商:ROHM 制造商全称:Rohm 功能描述:High Reliability Serial EEPROMs
BU9889GUL-W 制造商:ROHM 制造商全称:Rohm 功能描述:WL-CSP EEPROM family I2C BUS
BU9889GUL-WE2 功能描述:电可擦除可编程只读存储器 电可擦除可编程只读存储器 Serial-2Wire 8Kb RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
BU9890GUL-W 制造商:ROHM 制造商全称:Rohm 功能描述:Silicon Monolithic Integrated Circuit
BU9890GUL-WE2 功能描述:电可擦除可编程只读存储器 电可擦除可编程只读存储器 Serial-2Wire 32Kb RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8
BU9891GUL-W 制造商:ROHM 制造商全称:Rohm 功能描述:WL-CSP EEPROM family Microwire Bus
BU9891GUL-WE2 功能描述:电可擦除可编程只读存储器 电可擦除可编程只读存储器 Serial 4Kb RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8